IO-C-2820N控制器

IO-C-2820N Controller

Compact design, easy to install and simple to use

产品概述/Product Description

IO-C-2820N控制模块是徐州穆克电液控制有限公司开发的系列化简单易用的通用型IO模块。产品设计紧凑且安装方便,适用于在控制柜或作业现场快速安装。这样既可以减少控制器的使用数量,也可以减少系统布线的复杂度、降低布线成本,满足客户需求。

IO-C-2820N control module is a series of simple and easy-to-use general-purpose IO modules developed by Xuzhou MOOK Electro-hydraulic Control Co. The product is compact and easy to install, suitable for quick installation in the control cabinet or on the job site. This not only reduces the number of controllers used, but also reduces the complexity of system wiring, lowers wiring costs and meets customer needs.

IO-C-2820N控制器

技术参数/Technical Data

工作电压/Operating Voltage

8~36V DC

工作温度/Operating Temperature

-40℃~+75℃

存储温度/Storage Temperature

-40℃~+85℃

相对湿度/Relative Humidity

45%~90%

电流消耗/Current consumption

无负载,在12V车辆电气系统中:200mA

无负载,在24V车辆电气系统中:100mA
No load, in 12V vehicle electrical system: 200mA

No load, in 24V vehicle electrical system: 100mA

最大负载电流/Maximum Load Current

30A

处理器单元/Processor Unit

16Bit 80MHz

存储/Storage

82KB SDRAM768KB FLASH

参数空间/Parameter space

2KB FRAM

防护等级/Protection class

IP66/67

外形尺寸/Dimension

158.6mm × 111mm × 40.4mm

通信接口/Communication Interface

CAN2.0B


技术参数/Technical Data

- 2 x CAN2.0B, 50 Kbit/s ~ 1 Mbit/s;

- 6 x VI, 0 to 5 V analogue signal inputs, 10 bits, multiplexable as current-type analogue signal inputs and highly effective switching inputs;

- 4 x PI, 1 Hz ~ 15 kHz, multiplexable as high effective switching inputs;

- 4 x RI, 0 to 20 KΩ, 10 bits, multiplexable as voltage type analogue signal input, current type analogue signal input and high effective switching input;

- 6 x DI, high-side >4V / low-side <1V software settable;

- 14 × DO, 2A high-side output, multiplexable as a high-effective switching input;

- 8 × DO, 4A high-side output, multiplexable as a high-sense switching input;

- 6 × PWM, 2A output, 10-bit current feedback, constant current control, multiplexable as a high effective switching input;

 - 1 × VERF 5V/100mA.

技术参数/Technical Data

工作电压/Operating Voltage

8~36V DC

工作温度/Operating Temperature

-40℃~+75℃

存储温度/Storage Temperature

-40℃~+85℃

相对湿度/Relative Humidity

45%~90%

电流消耗/Current consumption

无负载,在12V车辆电气系统中:200mA

无负载,在24V车辆电气系统中:100mA
No load, in 12V vehicle electrical system: 200mA

No load, in 24V vehicle electrical system: 100mA

最大负载电流/Maximum Load Current

30A

处理器单元/Processor Unit

16Bit 80MHz

存储/Storage

82KB SDRAM768KB FLASH

参数空间/Parameter space

2KB FRAM

防护等级/Protection class

IP66/67

外形尺寸/Dimension

158.6mm × 111mm × 40.4mm

通信接口/Communication Interface

CAN2.0B


端口描述 Port Description

输入端口/Input port

端口数量/No.

端口描述/Port description

DIH/DIL

6

默认为高有效开关量输入;

可复用为低有效开关量输入
Defaults to a high valid switching input;

Can be multiplexed to low valid switching inputs

PI/DIH

4

默认为频率输入;

可复用为高有效开关量输入
Defaults to frequency input;

Can be multiplexed as a highly effective switching input

CI/VI/RI/DIH

4

默认为4~20mA电流型模拟量信号输入

可复用为0~5V电压型模拟量输入;

可复用0~20KΩ电阻型模拟量输入;

可复用为高有效开关量输入;

作为CI/VI时,可诊断对地短路
Default is 4~20mA current type analog signal input;

Multiplexable to 0~5V voltage type analog input;

Multiplexable to 0~20KΩ resistance type analog input;

Can be multiplexed as highly effective switching input;

When used as CI/VI, it can diagnose short circuit to ground.

VI/CI/DIH

6

默认为0~5V电压型模拟量输入

可复用为4~20mA电流型模拟量输入

可复用为高有效开关量输入;

可诊断对电源、对地短路
Default is 0~5V voltage type analog input;

Multiplexable to 4~20mA current type analog input;

Can be multiplexed to high effective switch input;

Diagnose short circuit to power supply and ground

输出端口/Output port

端口数量/No.

端口描述/Port description

PWM/DIH/DOH

6

默认为PWM输出;

可复用为高有效开关量输入;

可复用为2A高边输出;

作为PWM/DOH时,可诊断对电源短路对地短路(对地电阻<6Ω负载超限断线(电流<10mA
Defaults to PWM output;

May be multiplexed to a highly active switching input;

Multiplexable to 2A high-side output;

When used as PWM/DOH, it can diagnose short circuit to power supply, short circuit to ground (resistance to ground<6Ω), load overrun, disconnection (current <10mA)

DOH(2A)/DIH

14

默认为2A高边输出;

可复用为高有效开关量输入;

作为DOH时,可诊断断线和对地短路
Defaults to 2A high-side output;

Can be multiplexed as a highly valid switching input;

Diagnostic for broken wires and short to ground when used as DOH

DOH(4A)/DIH

8

默认为4A高边输出;

可复用为高有效开关量输入;

作为DOH时,可诊断对地短路
Defaults to 4A high-side output;

Can be multiplexed as a highly valid switching input;

Diagnostic for short to ground when used as DOH


安装尺寸/Installation dimensions
IO-C-2820N控制器安装尺寸

服务承诺 Service Commitment

秉承“高效、完善”的理念,履行给每一个客户的承诺。

Adhering to the concept of "high efficiency and perfection", we fulfill the promise to every customer.

Quick in-depth response in 15 minutes

Provide solutions within 2 hours

Engineer on site within 48 hours

360 days service

Copyright 徐州穆克电液控制有限公司 版权所有